Preview for review. Values in [brackets] are placeholders until the engineer's test cases are in. The form is not connected yet.
Private beta on TestFlight · iPhone and iPad

Fast. Accurate.
Right on site.

MEP calculations reviewed by a licensed engineer, with the source behind every answer. Works offline, in shafts and basements with no signal.

2.1 Duct sizing · Supply airReviewed by P.Eng
Airflow[CFM]
LocationCeiling
Selected size
[W] × [H] in
[V] FPM ([m/s]) · [Δp] in.wg/100 ft
Source: firm standard T1 · roughness T2
HVACFirst

Duct sizing for supply, return and exhaust air.

PlumbingPlanned

Pipe sizing and fixture units.

FirePlanned

Sprinkler and standpipe checks.

ElectricalPlanned

Load and conductor sizing.

Why XMEP

Answers you can stand behind.

Fast

The answer while you are still standing there.

  • Works offline, no signal needed
  • One screen from input to selected size
  • New calculations arrive without an app update

Accurate

Reviewed by a licensed engineer.

  • Every calculation is checked by a P.Eng before release
  • Hand-calculated test cases for each one
  • Warnings when an input is out of range

Traceable

Every number shows where it came from.

  • Table and code reference beside each coefficient
  • Imperial first, SI shown in brackets
  • Export the steps for your submittal

How it works

Watch a calculation run.

Duct sizing, step by step. XMEP follows the same flow the engineer wrote, and shows the table behind every value.

Out of range → try the next size upINPUTAirflow, service,location[CFM] · SALOOKUP · T1Velocity andfriction limits≤ [Vmax] FPMCOMPUTEArea neededA = Q / V[A] ft²SELECT · T3/T4Nearest standardduct size[W] × [H] inCHECKVelocity and frictionin range?Colebrook fRESULTSelected size, withits sources✓ PassINPUTAirflow, service, location[CFM] · SALOOKUP · T1Velocity and friction limits≤ [Vmax] FPMCOMPUTEArea needed, A = Q / V[A] ft²SELECT · T3/T4Nearest standard duct size[W] × [H] inCHECKVelocity and friction in range?Colebrook fRESULTSelected size, with its sources✓ Pass

A screen recording of the real editor will replace this animation.

Runs fully offline
Calculations update over the air
Your project data stays on your device

How we work

Every calculation goes through four gates before it reaches you.

1

Written by an engineer

The logic is drawn as a flowchart from the engineer's own design method.

2

Tested by hand

Each one ships with hand-calculated cases. The app must match them.

3

Reviewed by a P.Eng

A licensed engineer signs off before release. No self-approval.

4

Released over the air

Approved calculations reach your device without an app update.

Private beta

Get on the TestFlight list.

We are adding a small group of engineers, designers and contractors each round. Tell us what you work on and we will send an invite when there is a spot.

  • Free during the beta
  • iPhone or iPad with iOS 17 or later
  • We never sell or share your email
Trades you work in
Thanks. This preview is not connected yet, so nothing was sent.

XMEP · Markham, Ontario, Canada

FAQ

Questions

Who checks the calculations?

Each calculation is written and reviewed by a licensed professional engineer before it is released, and tested against hand-calculated cases.

Does it replace my engineer's stamp?

No. XMEP helps you size and check quickly on site. Design responsibility stays with the engineer of record.

Does it work without signal?

Yes. Calculations run on your device. You only need a connection to receive new or updated calculations.

When is the public release?

We are in a private TestFlight beta. Join the list and we will let you know when it opens.